Obersound, collections 5.5 designers

Die innovative Kollektion perforierter Akustikpaneelen. 25 Modelle, entworfen für Oberflex von der Agentur 5.5 designers.

Modelle

Climate Collection

Snow
Snow
Ash OD 728
Wind
Wind
Sycamore
Fog
Fog
Limed Oak
Rain
Rain
American Walnut T160
Sun
Sun
Figured Movingui

Skin Collection

Gooseflesh
Gooseflesh
Sycamore
Beauty Spot
Beauty Spot
Canadian Maple
Life line
Life line
Wenge-tinted Oak
Scale
Scale
American Walnut T266
Fur
Fur
Rosewood

Plant Collection

Meadow
Meadow
American Walnut T292
Twig
Twig
Anigre
Liana
Liana
Natural Oak
Copse
Copse
Bog-Oak-tinted Oak
Bark
Bark
American Walnut T9

Couture Collection

Canvas
Canvas
Canadian Maple
Patchwork
Patchwork
American Walnut T266
Scot
Scot
Anigre
Jersey
Jersey
Anigre T448
Padding
Padding
Rosewood

Vibration Collection

Amplitude
Amplitude
American Walnut T160
Crackling
Crackling
Slate-grey Oak T308
Frequency
Frequency
Ashen Oak T310
Wave
Wave
Grey Oak T309
Rhythm
Rhythm
Ash FR101

Produktansicht


Eigenschaften

VERBUND geschreinert • massiv (je nach Artikel)
OBERFLÄCHE

pore • satin • matt • gebürstet  (je nach Artikel)

AUFLAGE MDF (schwarz oder braun, je nach Artikel)
DICKEN DER AUFLAGEN 16 mm
FORMATE 249 x 120 cm • 249 x 60 cm • 249 x 40 cm
Bitte nehmen Sie für weitere Formate mit uns Kontakt auf
GEGENGEWICHTUNG A/C: 1 Vorderseite • 1 Ausgleichsseite
PERFORATIONEN

25 Perforationsmodelle in 5 Kollektionen (siehe Kollektionen)

Sehen Akustik Leistungen

KANTENFERTIGUNG mit Oberflex-Kantenband beschichtet • unbearbeitet •
bitte kontaktieren Sie uns für weitere Möglichkeiten
Kantenbänder
BEHANDLUND DER KANTEN geeichte • auf folgende Art gespant: Rillen, Fugen, Gehrungsschnitt
FEUERSCHUTZKLASSE Auf Anfrage:
M1 (n° 9152-00 du SNPE)
Bs1d0 (PV N°09AN0343)

Download: Technisches Datenblatt

 Laden Sie die Leistungserklärung Obersound, collections 5.5 Designers - Klasse B

Mise en oeuvre

The panels should be fabricated in compliance with Specification NF XP B 54-202 : «Panneaux décoratifs plaqués-bois – Spécifications (Decorative, wood-veneered panels - Specification) or equivalent.

Wall installation

Download the technical datasheet

 

Ceiling installation

Download the technical datasheet

On-site fabrication conditions

Fabrication should normally take place in the following conditions:

  • Prior to installation, the panels must be stabilized to ambient conditions. To this effect, store them for at least 3 days in a flat position in the place where they are eventually to be installed.
  • When installing the panels, allow for a 1 mm/m expansion joint.
  • Increase that joint to 1.5 mm/m in the following cases :
    - for rooms likely to be subjected to major atmospheric humidity variations
    - in cases where flame-retardent (M1-rated) panels are used.

On-site conditions

The rooms where the panels are to be installed should normally conform to the following conditions:

  • they should be roofed
  • they must have been heated or air-conditioned for at least 24 hours
  • all cement and plasterworks should be dry
  • ambient temperature must not fall to below 15° C
  • ambient air humidity during the stabilization process and at the time of installation should respond to the following criteria

If the panels are installed in a dry area: The relative air humidity during the stablilization phase should be within the range of 40 to 60%. Once the panels are installed, the ambient air humidity may exceed 65% only for a couple of weeks per annum.

If the panels are installed in a humid area (bonded to a hydrophobic substrate):

The relative air humidity during the stabilization phase may exceed the range of 40 to 60%.

Once the panels are installed, the ambient air humidity may exceed 85% only for a couple of weeks per annum.

Projekte

Neue akustische Lösungen: Obersound Holzpaneele, überarbeitet von den 5.5 Designern

Obersound, collection 5.5 designers

Paris - Design : Studio Norguet

MCDONALD' S - Concept Racine

Montreuil - Agences d'architecture : Agences Béchu et Volume ABC

Tribunal de Montreuil

Paris - Architekturbüro : Fendler Seemuller Architecture

Finaltis

Paris- Architecture ACD-Girardet

Roland Garros

Paris - Architekturbüro : Francis Krempp

Institution Internationale